 |
1)
Point the rifle
in a safe direction and remove the magazine from the rifle. |
 |
2)
Open the bolt
and pull it to the rear of the action body (receiver).
Note: Examine rifle to make sure it is unloaded.
|
 |
3)
Rotate the
breech bolt head counter clockwise until it locks in the 12
o'clock position. |
 |
4)
Remove the bolt. |
 |
5) Unscrew the front nose cap screw. |
 |
6)
Remove the
front nose cap screw from the nose cap. |
 |
7) Unscrew the
rear nose cap screw. |
 |
8) Remove the rear nose cap screw from the nose
cap. |
 |
9)
Remove the nose cap. |
 |
10)
Unscrew the rear swivel screw. |
 |
11) Remove the rear
swivel screw and the sling swivel. |
 |
12) Spread slightly the lower band and
remove from the stock. |
 |
13) Remove the upper hand guard.
|
 |
14) Unscrew the inner band screw. |
 |
15) Remove the inner band screw. |
 |
16) Unscrew the front trigger guard screw.
|
 |
17) Unscrew the rear trigger guard screw. |
 |
18) Remove the rear trigger guard screw. |
 |
19) Remove the front trigger guard screw. |
 |
20) Do not force the trigger guard out. If
the trigger guard is stuck in place, lightly
tap on the sides of the arch until it can be
easily removed.
|
 |
21) Use a piece of wood and tap lightly at
the top rear of the fore-end stock, on both sides.
You want to walk the rear of the fore-end
stock off on the barreled action. When
following steps 21, 22, and 23 only tap the
stock a small amount/distance. This will
prevent the stock from being damaged. |
 |
22) Then tap lightly on the fore-end stock at the front of the
receiver/action. |
 |
23) Then alternate back to tapping lightly
on the rear of the fore-end stock until the
fore-end stock can be removed easily |
 |
24) Lift the fore-end off and set aside. |
 |
25) Lift the rear sight and then remove the
lower hand guard. |
 |
26) Unscrew the upper butt plate screw. |
 |
27) Remove the upper butt plate screw.
|
 |
28) Unscrew the lower butt plate
screw.
|
 |
29) Remove the lower butt plate screw.
|
 |
30) Remove the butt plate. |
 |
31) Remove the felt wad with a cut-off clothes
hanger (as shown in figure 31). The hanger easily hooks felt wad. |
 |
32) Insert a large flat blade screwdriver into
the butt stock and place in groove of the stock
bolt. |
 |
33) Using large pliers, unscrew the stock bolt
counter-clockwise. |
 |
34) Separate the butt stock from the butt
stock socket.
|
 |
35) Figure 35 shows the stock bolt.
|
 |
36) Unscrew the rear, rear swivel screw. |
 |
37) Remove the rear, rear swivel screw. |
 |
38) Unscrew the front, rear swivel screw. |
 |
39) Remove the front, rear swivel screw. |
 |
40) Remove the rear swivel. |
 |
41) Unscrew the safety spring screw. |
 |
42) Remove the
safety spring screw. |
 |
43) Remove the
safety spring. |
 |
44) Remove the safety catch washer. |
 |
45)
Remove the safety catch and locking bolt from the
action body (receiver).
Note: I recommend you leave the safety catch
and locking bolt assembled.
|
 |
46) Figure 46 shows the safety catch and
locking bolt unassembled. |
 |
47) Unscrew the retaining spring screw. |
 |
48) Remove the retaining spring screw. The sear
spring and sear (pictured in figure 48) will fall out of the action body. |
 |
49) Remove the retaining spring. |
 |
50) Drive out the
magazine catch pin. |
 |
51) Remove the magazine catch. |
|
Reassembly Instructions |
 |
52) Replace the magazine catch. |
 |
53) Replace the retaining spring. |
 |
54) Replace the sear as shown in figure 54. |
 |
55) Replace the retaining spring screw. |
 |
56) Tighten the retaining spring screw. |
 |
57) Figure 57 shows the correct orientation
of the sear spring. |
 |
58) Compress the sear spring and install so
its ends fit into the grooves in the front
of the sear and the rear of the magazine
catch. |
 |
59) Figure 59 shows the correctly assembled
sear, magazine catch, sear spring, retaining
spring, and retaining spring screw. |
 |
60) Figure 60 shows the locking bolt and
safety catch correctly assembled prior to
installation. |
 |
61)
Replace the safety catch and locking bolt. |
 |
62) Replace the safety catch washer. |
 |
63) Figure 63 shows the correct orientation
of aligning the safety spring and the safety
catch washer. |
 |
64) Flip over the safety spring and align
the guide in the channel of the safety catch
washer. |
 |
65) Replace the safety spring screw. |
 |
66) Tighten the safety spring screw. |
 |
67) Work the safety to make sure it
functions properly and does not bind. |
 |
68) Replace the rear swivel. |
 |
69) Replace the rear, rear swivel screw. |
 |
70) Tighten the rear, rear swivel screw. |
 |
71) Replace the rear, rear swivel screw. |
 |
72) Tighten the rear, rear swivel screw. |
 |
73) If removed insert the stock bolt into
the rear of the butt stock. |
 |
74) Reinsert butt stock into butt socket. |
 |
75) Insert a large flat blade screw
driver into the butt stock trap. |
 |
76) Using a pair of pliers, turn large flat
blade screw driver clockwise until stock
bolt is tight. |
 |
77) Reinsert the stock bolt wad into the
butt stock trap of the butt stock. |
 |
78) Using clothes hanger, push the stock
bolt wad all of the way down until it rest
flat on the stock bolt. |
 |
79) Install the butt plate. |
 |
80) Replace the upper butt plate screw. |
 |
81) Tighten the upper butt plate screw. |
 |
82) Replace the lower butt plate screw. |
 |
83) Tighten the lower butt plate screw. |
 |
84) Lift the rear sight. |
 |
85) Reinstall lower hand guard. |
 |
86) Lower the rear sight. |
 |
87) Insert the barreled action into the
fore-end stock. Align the inner band so the
threaded lug points downward and the band
fits into the channel in the fore-end stock. |
 |
88) Slide the fore-end stock till it snuggly
rests up against the butt socket (as shown
in figure 88). If necessary use a small
wooden dowel and tap lightly into place. |
 |
89) Replace the inner band screw. |
 |
90) Tighten the inner band screw. |
 |
91) Replace trigger guard. |
 |
92) Reinstall the front trigger guard screw. |
 |
93) Replace rear guard screw. |
 |
94) Tighten the front and rear guard screws. |
 |
95) Install the forward handguard. |
 |
96) Spread slightly the lower band and
replace on the stock. |
 |
97) Replace the rear swivel screw and the
sling swivel. |
 |
98) Tighten the rear swivel screw. |
 |
99) Replace the front nose cap. |
 |
100) Replace the rear nose cap screw. |
 |
101) Tighten the rear nose cap screw. |
 |
102) Replace the front nose cap screw. |
 |
103) Tighten the front nose cap screw. |
 |
104) Make certain the safety is in the
forward position.
Insert the bolt with the flat side of the
bolt head pointing to twelve o'clock. |
 |
105) Snap the bolt head down. |
 |
106) Push the bolt forward. |
 |
107) Insert the magazine and lock into
place. |
 |
108) Figure 108 shows the reassembled rifle. |
| |
