 |
1)
With the rifle pointed in a safe direction,
open the bolt and make sure the rifle is not
loaded.
|
 |
2)
While depressing the trigger, remove the
bolt from the receiver. |
 |
3)
Unscrew the cleaning rod. |
 |
4)
Remove the cleaning rod. |
 |
5)
Unscrew the tang screw. |
 |
6)
Remove the tang screw. |
 |
7)
Unscrew the trigger guard screw. |
 |
8)
Remove the trigger guard screw. |
 |
9)
Remove the trigger guard by pulling straight
upwards. |
 |
10)
Depress the floor plate latch. |
 |
11)
Open the floor plate. |
 |
12) Depress the magazine follower and
compress the follower spring. |
 |
13) Remove magazine follower and floor plate
assembly from magazine. |
 |
14) Unscrew the forward band screw. |
 |
15) Remove the forward band screw. |
 |
16) Remove the forward band. |
 |
17) Unscrew the rear band screw.
|
 |
18) Remove the rear band screw.
|
 |
19) Slide the rear band forward. |
 |
20) Remove the handguard. |
 |
21) Lift barrel and receiver from stock.
|
 |
22) Unscrew the upper butt plate screw. |
 |
23) Remove the upper butt plate screw.
|
 |
24) Unscrew the lower butt plate screw. |
 |
25) Remove the lower butt plate screw. |
 |
26) Remove the butt plate. |
 |
27) Unscrew the bolt stop screw. |
 |
28) Remove the bolt stop screw. |
 |
29) Using a pointed object push the trigger
pin out of the trigger. |
 |
30) Note that in figure 30 there is a coiled
spring that is held in place by the trigger
pin.
|
 |
31) Remove the trigger and bolt stop. |
 |
32) Separate the trigger and bolt stop.
|
|
Note: The m/28
differs from the typical Mosin-Nagant as it
does not have a separate ejector and ejector
spring. The m/28 is a single piece unit.
|
 |
33) Unscrew the ejector screw.
|
 |
34) Remove the ejector screw.
|
 |
35) Tap the ejector forward. |
 |
36) Remove the ejector.
|
|
Reassembly
Instructions |
 |
37) Insert the ejector into the g4roove in
side of receiver as shown in figure 37. |
 |
38) Tap the ejector to the rear so the hole
is lined up with the threaded hole in the
receiver. |
 |
39) Insert the ejector screw. |
 |
40)
Tighten the ejector screw. |
|
Note: The m/28
trigger components differ from the typical
Mosin-Nagant in that there is an additional
spring that is inserted in the rear of the
trigger and held in place when the trigger
pin is inserted. |
 |
41) Combine the trigger and bolt stop. |
 |
42)
Combine the trigger and bolt stop as
shown in figure 42.
|
 |
43) Note the coiled spring inserted into
trigger and the bolt stop. The trigger pin
when inserted will hold the spring in place.
Insert the trigger and bolt stop.
|
 |
44) Insert the trigger pin. Note position of
spring ends. |
 |
45) Install the bolt stop screw.
|
 |
46) Tighten the bolt stop screw. |
 |
47) Work the trigger to ensure there is no
binding. |
 |
48) Install the butt plate.
|
 |
49) Install the lower butt plate screw.
|
 |
50) Tighten the lower butt plate screw.
|
 |
51) Install the upper butt plate screw. |
 |
52) Tighten the upper butt plate screw.
|
 |
53) Insert the barrel and receiver into the
stock. |
 |
54) Depress the magazine follower and
compress the follower spring and then replace the magazine follower and floor
plate assembly in the magazine.
|
 |
55) Allow the magazine follower spring to
expand.
|
 |
56) Close the floor plate and depress the
floor plate latch to latch in place. |
 |
57) Replace the trigger guard.
|
 |
58) Replace the trigger guard screw.
|
 |
59) Tighten the trigger guard screw.
|
 |
60) Replace the
tang screw.
|
 |
61) Tighten the
tang screw. |
 |
62) Install handguard up against the rear
sight. |
 |
63) Slide the rear band onto the stock and
handguard.
|
 |
64) Slide the rear band to the rear. |
 |
65) Insert the rear band spring screw. |
 |
66) Tighten the rear band spring screw. |
 |
67) Slide the forward band onto the stock
and handguard. |
 |
68) Insert the forward
band screw. |
 |
69) Tighten the forward
band screw. |
 |
70) Insert the cleaning rod. |
 |
71) Tighten the cleaning rod. |
 |
72) Insert the bolt. |
 |
73) Push the bolt
all the way forward. |
 |
74) Close the bolt. |
| |
